Thursday, January 17, 2013

Fabric Pendant Tutorial

I want to share with you how to make these Ice Resin pendants.  As I have mentioned in a previous post, as part of my New Year's resolution, I would like to try and make something other than a quilt using fabric and write a tutorial on how I made it each month this year.  These pendants are a way for fabric lovers to be able to wear a piece of their favorite fabric treasures on a daily basis.  I particularly like that encased in resin, it then becomes perfectly protected and sealed forever for a special keepsake.  Wear it on a chain, a piece of leather or anything you like and it will be sure to draw attention.

Materials needed:

--Ice Resin - Part A (Resin) & Part B (Hardener) 
--Mod Podge
--Paint brush
--Measuring cups
--Tongue depressors
--Silver bezel (You can use any sort of bezel that you like.)
--Large stable piece of cardboard
--Small piece of lightweight cardboard
--Scissors
--Syringe
--Sharp pencil
--Needle or pin
--Plastic cover
--Level working surface



I purchased my Ice Resin in Australia from this site here: Sunset Designs.  You also receive the measuring cups and tongue depressors with the purchase of the Ice Resin.

Mod Podge can be purchased at most craft type stores.  I purchased mine at Spotlight in Australia.

The silver bezels I purchased from this wonderful Etsy seller: Captured Moments.  She is very fast with shipping.  Of course you can use any sort of bezel you would like, I just liked the handcrafted look of these ones.

For the syringe, I used extras I had on hand saved from the children's Panadol medicine.  Make sure you use one that is larger rather than smaller.  Using a syringe will help you avoid having to do clean ups and is very helpful.

 All right, let's begin!


In order to audition areas of your chosen fabric and to find the best placement to fit into the pendant, it will be helpful to make a viewfinder.  Use the small lightweight cardboard piece and use the sharp pencil to trace around the silver bezel.  Use the scissors to cut out the drawn shape making sure to cut on the inside of the drawn line.

Select your chosen fabric and using the view finder trial different options until a pleasing effect is found.

Using the pencil lightly trace against the cut area of the viewfinder directly onto the fabric.  Cut the fabric just to the inside of the drawn line.

Carefully place the cut fabric piece inside the bezel.  Make sure fabric lies flat within the bezel and that it covers the entire base area.  Check that there are no loose threads either underneath or at the edges of the fabric.

Next, take the clean paintbrush, Mod Podge and silver bezel now filled with fabric and get ready to paint.

Coat the fabric with a thin layer of Mod Podge taking care not to let any one area have too much.  This is necessary in order to help keep the fabric from lifting up or shifting after the resin is put inside the bezel.  Let the layer of Mod Podge dry completely.  This may take a few hours.

Prepare the Ice Resin mixture.  Use two measuring cups, the tongue depressor for stirring and parts A and B of the Ice Resin solution to mix the Ice Resin.

It is better to mix the ice resin at room temperature or warmer, if working in a cooler room the resin mixtures can be warmed by running warm water over the sealed bottles or in a warm bottle bath.  This helps reduce bubbles and helps the mixture to pour smoother.  Starting with part A resin solution pour out an exact measurement into the measuring cup.  It is very important to measure exact amounts otherwise your Ice Resin mixture will not cure properly.

 Measure out the exact same amount of the Part B resin hardener into the second measuring cup.

Again, it is important to have equal amounts of both Part A Resin and Part B Hardener otherwise proper curing will not occur.  It is better to have a drop or two more of the hardener rather than the other way around.

Slowly pour Part B hardener into the cup containing the Part A Resin.  Make sure to scrape every last bit into the cup.

 Slowly stir the mixture for two full minutes.

Create an elevated area using the tongue depressors by placing them in parallel lines.  Place the silver bezel on top of the tongue depressors in order to allow the bezel to sit up high free from tilting on the cardboard surface.

 Prepare enough bezels for pouring the entire Ice Resin mixture.  The mixture is no longer good after about 45 minutes and must be thrown out so it is best to prepare ahead of time so that the mixture can be poured in a timely fashion.  Using the syringe will be an immense help in keeping a steady hand and eliminating spills.

Using the syringe, suck up an amount of the Ice Resin mixture and slowly expel it into the first bezel.  Going slowly will reduce the amount of bubbles.

Continue filling gently pulling the mixture to the corners of the bezel.  Get down at eye level, watch and continue filling until the mixture is slightly higher than the level of the bezel.  Add one drop at a time if necessary.  Continue to fill each bezel as mixture amount allows.

In this case there was more mixture than bezels allowed for, so another bezel was added to use the entire mixture.

Use the needle and gently poke any bubbles that form.  It is important to check a couple times for the first couple hours after pouring.  Try not to knock anything!  Spills are best cleaned using baby wipes if you have them on hand as the oil in the wipes will help break up the resin. 

Cover all the bezels with the plastic cover to prevent dust from getting on the surface.  Check every half an hour or so for bubbles for a couple of hours and then leave for it to harden for 24 hours.  It takes a full 3 days for the fabric pendants to cure properly.



So here it the final result.  Please feel free to ask me any questions or make any suggestions on better methods you might find along the way.  Also, I would love to see what you create, so please stop by and show me what you've created using this tutorial.  Thank you!

13 comments:

Debbie said...

These are very cool!

Lara said...

Super cool!

A Ö said...

This is so cool, Thank you!!!

Mama Spark said...

What a fab idea! I can't wait to try making these sometime soon!!!

Rori said...

Fantastic tutorial! Thanks so much. We just made a copper penny countertop with resin and another way to pop the bubbles is to "huff" on it with your breath, like huffing on a cold window to create condensation. It is the carbon dioxide in your breath which pops the bubbles.

I need to go find some more resin now and some cute fabric.

Thanks again

Lynne said...

SO cool. Excellent tutorial. Thanks so much for sharing!

~Diana said...

Great tutorial...thanks for sharing!

bluquilt said...

Great tutorial! Very detailed. Thanks for the links to suppliers, too.

chrisee said...

Great easy to follow tutorial.
You make is look sooo easy!
Thankyou.

fiberchick said...

Fabuloso!!!

Stephanie said...

HI Jeannette,
Love this tutorial, definitely going to give it a go. Can I ask you where you got your supplies from. Do Spotlight have them????

Stephanie said...

HI Jeannette,
Love this tutorial, definitely going to give it a go. Can I ask you where you got your supplies from. Do Spotlight have them????

Amanda Bianchi said...

Wonderful tutorial!! I have some fabric scraps that my grandmother used to make me a quilt when I was a little girl and I have never been able to part with them. Now I can wear a part of her with me!! Thanks so much!!

Total Pageviews